* Remove unnecessary type conversions
* Consolidate repeated strings into consts
* Clothe return statements
* Update blockchain/v1/reactor_fsm_test.go
Co-Authored-By: Anton Kaliaev <anton.kalyaev@gmail.com>
This PR repairs linter errors seen when running the following commands:
golangci-lint run --no-config --disable-all=true --enable=unconvert
golangci-lint run --no-config --disable-all=true --enable=goconst
golangci-lint run --no-config --disable-all=true --enable=nakedret
Contributes to #3262
* init of (2/2) common errors
* Remove instances of cmn.Error (2/2)
- Replace usage of cmnError and errorWrap
- ref #3862
Signed-off-by: Marko Baricevic <marbar3778@yahoo.com>
* comment wording
* simplify IsErrXXX functions
* log panic along with stopping the MConnection
* p2p: fix false-positive error logging when stopping connections
This changeset fixes two types of false-positive errors occurring during
connection shutdown.
The first occurs when the process invokes FlushStop() or Stop() on a
connection. While the previous behavior did properly wait for the sendRoutine
to finish, it did not notify the recvRoutine that the connection was shutting
down. This would cause the recvRouting to receive and error when reading and
log this error. The changeset fixes this by notifying the recvRoutine that
the connection is shutting down.
The second occurs when the connection is terminated (gracefully) by the other side.
The recvRoutine would get an EOF error during the read, log it, and stop the connection
with an error. The changeset detects EOF and gracefully shuts down the connection.
* bring back the comment about flushing
* add changelog entry
* listen for quitRecvRoutine too
* we have to call stopForError
Otherwise peer won't be removed from the peer set and maybe readded
later.
* Remove deprecated PanicXXX functions from codebase
As per discussion over
[here](https://github.com/tendermint/tendermint/pull/3456#discussion_r278423492),
we need to remove these `PanicXXX` functions and eliminate our
dependence on them. In this PR, each and every `PanicXXX` function call
is replaced with a simple `panic` call.
* add a changelog entry
* p2p: refactor Switch#Broadcast func
- call wg.Add only once
- do not call peers.List twice!
* bad for perfomance
* peers list can change in between calls!
Refs #3306
* p2p: use time.Ticker instead of RepeatTimer
no need in RepeatTimer since we don't Reset them
Refs #3306
* libs/common: remove RepeatTimer (also TimerMaker and Ticker interface)
"ancient code that’s caused no end of trouble" Ethan
I believe there's much simplier way to write a ticker than can be reset
https://medium.com/@arpith/resetting-a-ticker-in-go-63858a2c17ec
* p2p/conn: fix deadlock in FlushStop/OnStop
* makefile: set_with_deadlock
* close doneSendRoutine at end of sendRoutine
* conn: initialize channs in OnStart
Fixes#2715
In crawlPeersRoutine, which is performed when seedMode is run, there is
logic that disconnects the peer's state information at 3-hour intervals
through the duration value. The duration value is calculated by
referring to the created value of MConnection. When MConnection is
created for the first time, the created value is not initiated, so it is
not disconnected every 3 hours but every time it is disconnected. So,
normal nodes are connected to seedNode and disconnected immediately, so
address exchange does not work properly.
https://github.com/tendermint/tendermint/blob/master/p2p/pex/pex_reactor.go#L629
This point is not work correctly.
I think,
https://github.com/tendermint/tendermint/blob/master/p2p/conn/connection.go#L148
created variable is missing the current time setting.
* p2p/conn: FlushStop. Use in pex. Closes#2092
In seed mode, we call StopPeer immediately after Send.
Since flushing msgs to the peer happens in the background,
the peer connection is often closed before the messages are
actually sent out. The new FlushStop method allows all msgs
to first be written and flushed out on the conn before it is closed.
* fix dummy peer
* typo
* fixes from review
* more comments
* ensure pex doesn't call FlushStop more than once
FlushStop is not safe to call more than once,
but we call it from Receive in a go-routine so Receive
doesn't block.
To ensure we only call it once, we use the lastReceivedRequests
map - if an entry already exists, then FlushStop should already have
been called and we can return.
* Disable transitioning to new round upon 2/3+ of Precommit nils
Pull in ensureVote test function from https://github.com/tendermint/tendermint/pull/2132
* Add several ensureX test methods to wrap channel read with timeout
* Revert panic in tests
except now we calculate the max size using the maxPacketMsgSize()
function, which frees developers from having to know amino encoding
details.
plus, 10 additional bytes are added to leave the room for amino upgrades
(both making it more efficient / less efficient)
As both configs are concerned with the p2p packaage and PeerConfig is
only used inside of the package there is no good reason to keep the
couple of fields separate, therefore it is collapsed into the more
general P2PConifg. This is a stepping stone towards a setup where the
components inside of p2p do not have any knowledge about the config.
follow-up to #1325
* use increment and decrement operators.
* remove unnecessary else branches.
* fix package comment with leading space.
* fix receiver names.
* fix error strings.
* remove omittable code.
* remove redundant return statement.
* Revert changes (code is generated.)
* use cfg as receiver name for all config-related types.
* use lsi as the receiver name for the LastSignedInfo type.
don't bother with this "only ping when we havent heard from them". lets
just always ping every peer from the sendRoutine every 10s no matter
what. if they dont pong within pongTimeout, disconnect :)
Phil Salant
Marko
Anton Kaliaev
Thane Thomson
Ethan Buchman
Ismail Khoffi
Zarko Milosevic
Matthew Slipper
Dev Ojha
Zach Ramsay
Liamsi
Alexander Simmerl
Jae Kwon
Thomas Corbière
zbo14