An interface can have both a /64 and a /128 from a provider.
In such a case, use the address from the /64 to do the ping check, not
the /128.
Signed-off-by: Brian J. Murrell <brian@interlinx.bc.ca>
Pinging IPv6 hosts using an interface as a source specifier seems
troublesome. See https://bugs.openwrt.org/index.php?do=details&task_id=2897
for more detail.
Use the desired source interface's IP address instead.
Signed-off-by: Brian J. Murrell <brian@interlinx.bc.ca>
Till now we could only ping http targets on port 80. With this change by
adding the config boolean config option httping_ssl we could also ping
https ping targets on port 443.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Sometimes the return value of `ubus -S call network.interface.wan status`
cause `json_load` to return `Failed to parse message data` error.
To avoid this, the JSON data always should be quoted with double quotes.
Signed-off-by: Evren Yurtesen <eyurtese@abo.fi>
Removed quoatation marks from commit heading
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This bug was introduced since dd206b7d0b
mwan3_remon_ipv4 and mwan3_remon_ipv6 is command to run not a variable
I add some comments on them hopefully people will notice it
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Before this change two disconnected events were generated. This is wrong!
The disconnected event is impliciet generated by the hotplug script on ifdown
event. The mwan3track script is notified by a USR1 signal which
generates the disconnectd event. The additional "disconnectd" event on
ifdown is not required.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Add to ubus the missing output information "policies" which could already
be observed with the command "mwan3 status".
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
If we set the option "local_source" in the globals mwan3 section to "none",
traffic generated by the router it self will always use the default route from
the wan interface with the lowest metric. If this interface is down
the router traffic still uses the connection with the lowest metric but
this is disconnected. Load balancing and failover from the lan site is
still possible. Only router generated traffic is not load balanced and
could not use failover.
To solve this issue with router initiated traffic add the additional
option "online_metric" to the mwan3 interface section.
If the interface is connected then this lower "online metric" is set in the
default routing table.
With this change we have at least a failover with router initiated
traffic.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Get downtime information for the tracked mwan3 wan interfaces.
The information shows how long this interface is in disconnected state.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Get uptime information for the tracked mwan3 wan interfaces.
The information shows how long this interface is in connected state.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
If a interface is down, call ubus will return an null message which is
used to json_load, it causes json_get_vars gets value from last load and
l3_device various is nonzero.
Signed-off-by: Kyson Lok <kysonlok@gmail.com>
Move setting global enabled flag from /etc/init.d/mwan3 to mwan3
command. So we could start mwan3 from the cmd mwan3 as well.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Only execute an ifup event with the command "mwan3 ifup <iface>" if the
l3_device is found in the ubus "network.interface.<iface>".
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
1. Test link quality based on packet loss & latency w.r.t. pre-defined high and low watermark values.
2. Extended ubus support to provide packet loss & latency information per wan per track_ip
Signed-off-by: Nishant Sharma <codemarauder@gmail.com>
To fix the shell local issue in the ubus mwan3 rpcd shell script, move
the switch case statment into a function.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
We need always three of the firewall mask value for
* default routing table
* blackhole
* unreachable
the other will be used for the interfaces.
* If we have set the mmx_mask to max 0xFF00 (8 bit set) we could use max 252
interfaces.
* If we have set the mmx_mask to min 0x0E00 (3 bit set) we could use max 4
interfaces.
Only the ones are counting from the firewall mask value.
Minimal three firewall mask bit vaules must be set.
Maximal eight firewall mask bit vaules could be set.
Table overview mmx_mask value bits vs. max interfaces
mmx_mask value bits set 1 -> not usefull
mmx_mask value bits set 2 -> not usefull
mmx_mask value bits set 3 -> 4 Interfaces (mask example 0x0E)
mmx_mask value bits set 4 -> 12 Interfaces
mmx_mask value bits set 5 -> 28 Interfaces
mmx_mask value bits set 6 -> 60 Interfaces
mmx_mask value bits set 7 -> 124 Interfaces
mmx_mask value bits set 8 -> 252 Interfaces (mask example 0xFF)
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Add a new ACTIONs:
* connected ACTION is called once if mwan3track reach all configured track_ips
* disconnected ACTION is called once if mwan3track is unable to reach the track_ips
The connected/disconnected will called only by mwan3track in opposite
the ACTIONs ifup/ifdown will also be called by netifd.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Move all shell commands which are executed during /lib/mwan3/mwan3.sh
sourceing into a seperate init function which must be called at first.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
In some situation it is not enough to send a SIGTERM to mwan3track to
ask service to stop accurate. If this does not work send him a SIGKILL
to prevent mwan3track running more then once per interface.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Florian Eckert
Aaron Goodman
Brian J. Murrell
yurtesen
Chen Minqiang
Michael Stoll
Kyson Lok
Nishant Sharma