The strongswan-libnttfft package should not select the strongswan
package, but should depend on it instead. Otherwise a circular
dependency is created.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Derived from the ipsec initd script, with the following changes:
(1) various code improvements, corrections (get rid of left/right
updown scripts, since there's only one), etc;
(2) add reauth and fragmentation parameters;
(3) add x.509 certificate-based authentication;
and other minor changes.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
If you shutdown ipsec service, and it doesn't clean up
/var/ipsec/ipsec.conf, then when you start swanctl service it
might see an incompatible file on startup. Remedy is to
remove unneeded files when shutting down the service. They
can always be regenerated when the service starts again.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
These config files are only used by the ipsec interface to charon,
and shouldn't be part of the base package.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Having scripts diddle user written config files seems potentially
dangerous. Plus there's really no downside to including some
empty files. Best to just make the includes be permanent.
Additional feature suggested by Luiz: if a -opkg version of the
config file was created unnecessarily, remove it as part of the
upgrade process since changes won't be happening to that file
as an artifact of the service starting. The include lines are
now permanent, which means that (1) additional configuration
synthesized by UCI won't be anywhere that opkg (or sysupgrade,
for that matter) cares about since it won't be persistent, and
(2) if changes are being made, then they're being done by a
person with an editor and they really should be distinguished.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
This has been observed by myself and @luizluca: ip route get is
appending uid0 to the output, as seen from:
root@OpenWrt2:~# ip route get 1.1.1.1
1.1.1.1 via 174.27.160.1 dev eth3 src 174.27.182.184 uid 0
cache
root@OpenWrt2:~#
so the fix is an anchored match, discarding all else. Also, using
ip -o means never having to do multiline matches...
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
When building with strongswan-ipsec disabled, strongswan fails to build
because the ipsec.conf file does not exist. Fix this by moving the
ipsec.* files and directories to the strongswan-ipsec package.
Closes#10879 while keeping ipsec.conf to avoid breaking existing
setups, as opposed to #11709.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add a conffiles-section for the /etc/swanctl folder, which is used by the swanctl util. This will keep the configfiles during an sysupgrade.
Signed-off-by: Sven Roederer <S.Roederer@colvistec.de>
The CONTRIBUTING.md requests an (or multiple) SPDX identifier for GPL
licenses. But a lot of packages did use a different, non-SPDX style with a
"+" at the end instead of "-or-later".
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Ipsec user script (/etc/ipsec.user) now get called indirectly by openwrt
"/sbin/hotplug-call". So other packages could also install their scripts
in "/etc/hotplug.d/ipsec".
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The interface config option allows users to configure logical OpenWRT
interface names in the ipsec section; it allows StrongSwan to listen
and send traffic on specified interface(s). It translates to interfaces_use
StrongSwan option which is a comma sepearted list of network devices
that should be used by charon.
Since StrongSwan can only be started when one of the specified logical
OpenWRT interface is up procd interface triggers are installed to
trigger the reload script.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Since the strongswan-utils package now only contains the aging ipsec
utility, rename it to strongswan-ipsec.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
We currently include the SCEP client in strongswan-utils, which is a
dependency of the strongswan-default meta-package. As it's generally not
recommended to generate keys on embedded devices due to lack of entropy,
move the SCEP client to a separate package, and only depend on it in the
strongswan-full meta-package.
While at it, add scepclient.conf to the package.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
We currently include the PKI tool in strongswan-utils, which is a
dependency of the strongswan-default meta-package. As it's generally not
recommended to generate keys on embedded devices due to lack of entropy,
move the PKI tool to a separate package, and only depend on it in the
strongswan-full meta-package.
While at it, add pki.conf to the package.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Philip Prindeville
Eneas U de Queiroz
Derek Yerger
Stijn Tintel
Sven Roederer
Jan Pavlinec
Sven Eckelmann
Lucian Cristian
Moritz Warning
Magnus Kroken
Florian Eckert
Sebastian Kemper
Hans Dedecker