Up until now, we were defaulting to MIPS24K for all MIPS archs.
But, we should use the GENERIC target for MIPS{EL} and the MIPS24K target
for the 24kc CPU_TYPE.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The GENERIC target for OpenBLAS seems good enough for most configs, so try
to use it for MIPS64 and as default for other archs.
This was already being used for x86{_64} archs.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
If the user defines a $max_timeout of 30, the service will wait 30 seconds
before it considers lxc-stop complete even though lxc-stop might actually
finish much sooner. This introduces an unneeded delay.
This commit changes the behavior to check once per second to see when lxc-stop
actually stops doing so up to $max_timeout. It also slightly simplifies the
code with logic to append the -t $max_timeout to the script.
Signed-off-by: John Audia <graysky@archlinux.us>
Remove upstream backport.
Add patch fixing compilation with powerpc and musl.
Switch to AUTORELEASE for simplicity.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Testing showed that additional syscalls are needed on ARMv7.
Add "clock_gettime64" and "statx" which seem to be used now instead
of "clock_gettime" and "stat" syscalls which are already listed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A new server was added which runs within the OpenWrt cloud, it's much
faster and should be used instead. For development the server at
https://asu.aparcar.org stays available.
Signed-off-by: Paul Spooren <mail@aparcar.org>
When Open vSwitch is configured to use a controller, but is unable to
connect to it, Open vSwitch will setup flows to allow all traffic, if
the failure mode is not configured, or set to standalone.
As this might be a security hazard, it is also possible to configure
Open vSwitch in a secure failure mode. Enabling this mode causes Open
vSwitch to drop all traffic if it is unable to connect to the
controller.
Redirect stderr of the command to /dev/null as it does not support the
--if-exists option.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Due to a copy-paste error, libopenvswitch is missing a dependency when
Open vSwitch is configured to use unbound:
Package openvswitch-libopenvswitch is missing dependencies for the following libraries:
libunbound.so.8
Use the correct config symbol to solve this.
Fixes: 45c8cc9d8a ("openvswitch: make libunbound optional")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The genhash binary is only built when IPVS is enabled, so make its
installation depend on IPVS being enabled.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add a UCI config option to set the OpenFlow datapath description. This
allows setting a human readable description of the bridge, e.g.
"Building x, Floor y, AP z", which makes it easier to recognize the AP.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Upstream released 1.0.0, so change the package to the git tag 1.0.0
Mainly documentation and argument handling changes
Signed-off-by: Damien Mascord <tusker@tusker.org>
Rosen Penev
Moritz Warning
Alexandru Ardelean
Stan Grishin
Alexander Sulfrian
John Audia
Vladimir Ulrich
Zbyněk Kocur
Daniel Golle
Tianling Shen
Martin Weinelt
Paul Spooren
Seb Belcher
Florian Eckert
Stijn Tintel
Michal Vasilek
Damien Mascord
Josef Schlehofer