If you shutdown ipsec service, and it doesn't clean up
/var/ipsec/ipsec.conf, then when you start swanctl service it
might see an incompatible file on startup. Remedy is to
remove unneeded files when shutting down the service. They
can always be regenerated when the service starts again.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Having scripts diddle user written config files seems potentially
dangerous. Plus there's really no downside to including some
empty files. Best to just make the includes be permanent.
Additional feature suggested by Luiz: if a -opkg version of the
config file was created unnecessarily, remove it as part of the
upgrade process since changes won't be happening to that file
as an artifact of the service starting. The include lines are
now permanent, which means that (1) additional configuration
synthesized by UCI won't be anywhere that opkg (or sysupgrade,
for that matter) cares about since it won't be persistent, and
(2) if changes are being made, then they're being done by a
person with an editor and they really should be distinguished.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
This has been observed by myself and @luizluca: ip route get is
appending uid0 to the output, as seen from:
root@OpenWrt2:~# ip route get 1.1.1.1
1.1.1.1 via 174.27.160.1 dev eth3 src 174.27.182.184 uid 0
cache
root@OpenWrt2:~#
so the fix is an anchored match, discarding all else. Also, using
ip -o means never having to do multiline matches...
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
This commit allows for UCI configuration of the "left=" and the
"mark=" values in a StrongSwan IPSec connection. This improves
VTI support and allows certain stricter connection scenarios.
Signed-off-by: Michael C. Bazarewsky <github@bazstuff.com>
This is useful to assign all traffic to a fw3 zone, e.g.:
/etc/config/ipsec:
config remote 'test'
list tunnel 'dev'
...
config 'tunnel' 'dev'
option reqid '33'
...
/etc/config/firewall:
config zone
option name wan
option extra_src "-m policy --pol none --dir in"
option extra_dest "-m policy --pol none --dir out"
...
config zone
option name vpn
# subnet needed for firewall3 before 22 Nov 2019, 8174814a
list subnet '0.0.0.0/0'
option extra_src "-m policy --pol ipsec --dir in --reqid 33"
option extra_dest "-m policy --pol ipsec --dir out --reqid 33"
...
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
The interface config option allows users to configure logical OpenWRT
interface names in the ipsec section; it allows StrongSwan to listen
and send traffic on specified interface(s). It translates to interfaces_use
StrongSwan option which is a comma sepearted list of network devices
that should be used by charon.
Since StrongSwan can only be started when one of the specified logical
OpenWRT interface is up procd interface triggers are installed to
trigger the reload script.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Based on the ipsec running state reload_service is either reloading ipsec
or starting ipsec. However in the latter case it calls ipsec start which
bypasses the procd start_service function which means the running ipsec
instance is not managed by procd.
Fix this by calling start in case ipsec is not running; at the same time
add service_running function which is used by procd provided running
function.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
When the strongswan service is running, `ipsec status` returns 0. Check
the return value instead of checking its output.
While at it, remove the [[ ]] bashism, use rereadall instead of
(reread)secrets, and move it inside the if statement.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
In commit 36e073d820, some checks were
added to see if the UCI config file exists and if there are any peers
configured in it. Due to these checks, if /etc/config/ipsec exists, but
contains no enabled peers, strongswan will not be started. This is not
ideal, as a user might want to experiment with the UCI config while
keeping existing connections in /etc/ipsec.conf operational.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add support to configure strongswan via uci.
uci support is based on the following sections
-ipsec : Global config items belonging in the strongswan.conf file
-remote : Defines the remote peer(s)
-tunnel : Defines the IPSec connections in tunnel mode
-transport : Defines the IPSec connections in transport mode
-crypto_proposal : Defines the different crypto proposals
Signed-off-by: Pierre Lebleu <pme.lebleu@gmail.com>
Signed-off-by: Gino Peeters <peeters.gino@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Philip Prindeville
Michael C. Bazarewsky
Paul Fertser
Hans Dedecker
Stijn Tintel
Steven Barth