Peers

This document explains how Tendermint Peers are identified and how they connect to one another.

For details on peer discovery, see the peer exchange (PEX) reactor doc.

Peer Identity

Tendermint peers are expected to maintain long-term persistent identities in the form of a public key. Each peer has an ID defined as peer.ID == peer.PubKey.Address(), where Address uses the scheme defined in crypto package.

A single peer ID can have multiple IP addresses associated with it, but a node will only ever connect to one at a time.

When attempting to connect to a peer, we use the PeerURL: <ID>@<IP>:<PORT>. We will attempt to connect to the peer at IP:PORT, and verify, via authenticated encryption, that it is in possession of the private key corresponding to <ID>. This prevents man-in-the-middle attacks on the peer layer.

Connections

All p2p connections use TCP. Upon establishing a successful TCP connection with a peer, two handshakes are performed: one for authenticated encryption, and one for Tendermint versioning. Both handshakes have configurable timeouts (they should complete quickly).

Authenticated Encryption Handshake

Tendermint implements the Station-to-Station protocol using X25519 keys for Diffie-Helman key-exchange and chacha20poly1305 for encryption.

Previous versions of this protocol (0.32 and below) suffered from malleability attacks whereas an active man in the middle attacker could compromise confidentiality as described in Prime, Order Please! Revisiting Small Subgroup and Invalid Curve Attacks on Protocols using Diffie-Hellman.

We have added dependency on the Merlin a keccak based transcript hashing protocol to ensure non-malleability.

It goes as follows:

generate an ephemeral X25519 keypair
send the ephemeral public key to the peer
wait to receive the peer's ephemeral public key
create a new Merlin Transcript with the string "TENDERMINT_SECRET_CONNECTION_TRANSCRIPT_HASH"
Sort the ephemeral keys and add the high labeled "EPHEMERAL_UPPER_PUBLIC_KEY" and the low keys labeled "EPHEMERAL_LOWER_PUBLIC_KEY" to the Merlin transcript.
compute the Diffie-Hellman shared secret using the peers ephemeral public key and our ephemeral private key
add the DH secret to the transcript labeled DH_SECRET.
generate two keys to use for encryption (sending and receiving) and a challenge for authentication as follows:
- create a hkdf-sha256 instance with the key being the diffie hellman shared secret, and info parameter as TENDERMINT_SECRET_CONNECTION_KEY_AND_CHALLENGE_GEN
- get 64 bytes of output from hkdf-sha256
- if we had the smaller ephemeral pubkey, use the first 32 bytes for the key for receiving, the second 32 bytes for sending; else the opposite.
use a separate nonce for receiving and sending. Both nonces start at 0, and should support the full 96 bit nonce range
all communications from now on are encrypted in 1400 byte frames (plus encoding overhead), using the respective secret and nonce. Each nonce is incremented by one after each use.
we now have an encrypted channel, but still need to authenticate
extract a 32 bytes challenge from merlin transcript with the label "SECRET_CONNECTION_MAC"
sign the common challenge obtained from the hkdf with our persistent private key
send the amino encoded persistent pubkey and signature to the peer
wait to receive the persistent public key and signature from the peer
verify the signature on the challenge using the peer's persistent public key

If this is an outgoing connection (we dialed the peer) and we used a peer ID, then finally verify that the peer's persistent public key corresponds to the peer ID we dialed, ie. peer.PubKey.Address() == <ID>.

The connection has now been authenticated. All traffic is encrypted.

Note: only the dialer can authenticate the identity of the peer, but this is what we care about since when we join the network we wish to ensure we have reached the intended peer (and are not being MITMd).

Peer Filter

Before continuing, we check if the new peer has the same ID as ourselves or an existing peer. If so, we disconnect.

We also check the peer's address and public key against an optional whitelist which can be managed through the ABCI app - if the whitelist is enabled and the peer does not qualify, the connection is terminated.

Tendermint Version Handshake

The Tendermint Version Handshake allows the peers to exchange their NodeInfo:

type NodeInfo struct {
  Version    p2p.Version
  ID         p2p.ID
  ListenAddr string

  Network    string
  SoftwareVersion    string
  Channels   []int8

  Moniker    string
  Other      NodeInfoOther
}

type Version struct {
 P2P uint64
 Block uint64
 App uint64
}

type NodeInfoOther struct {
 TxIndex          string
 RPCAddress       string
}

The connection is disconnected if:

peer.NodeInfo.ID is not equal peerConn.ID
peer.NodeInfo.Version.Block does not match ours
peer.NodeInfo.Network is not the same as ours
peer.Channels does not intersect with our known Channels.
peer.NodeInfo.ListenAddr is malformed or is a DNS host that cannot be resolved

At this point, if we have not disconnected, the peer is valid. It is added to the switch and hence all reactors via the AddPeer method. Note that each reactor may handle multiple channels.

Connection Activity

Once a peer is added, incoming messages for a given reactor are handled through that reactor's Receive method, and output messages are sent directly by the Reactors on each peer. A typical reactor maintains per-peer go-routine(s) that handle this.

5.6 KiB Raw Blame History