LILiK
/
openwrt-packages-dist


								## apcupsd.conf v1.1 ##

								#

								#  for apcupsd release 3.14.1 (04 May 2007) - unknown

								#

								# "apcupsd" POSIX config file


								#

								# ========= General configuration parameters ============

								#


								# UPSNAME xxx

								#   Use this to give your UPS a name in log files and such. This

								#   is particularly useful if you have multiple UPSes. This does not

								#   set the EEPROM. It should be 8 characters or less.

								UPSNAME ups1


								# UPSCABLE <cable>

								#   Defines the type of cable connecting the UPS to your computer.

								#

								#   Possible generic choices for <cable> are:

								#     simple, smart, ether, usb

								#

								#   Or a specific cable model number may be used:

								#     940-0119A, 940-0127A, 940-0128A, 940-0020B,

								#     940-0020C, 940-0023A, 940-0024B, 940-0024C,

								#     940-1524C, 940-0024G, 940-0095A, 940-0095B,

								#     940-0095C, M-04-02-2000

								#

								UPSCABLE smart


								# To get apcupsd to work, in addition to defining the cable

								# above, you must also define a UPSTYPE, which corresponds to

								# the type of UPS you have (see the Description for more details).

								# You must also specify a DEVICE, sometimes referred to as a port.

								# For USB UPSes, please leave the DEVICE directive blank. For

								# other UPS types, you must specify an appropriate port or address.

								#

								# UPSTYPE   DEVICE           Description

								# apcsmart  /dev/tty**       Newer serial character device,

								#                            appropriate for SmartUPS models using

								#                            a serial cable (not USB).

								#

								# usb       <BLANK>          Most new UPSes are USB. A blank DEVICE

								#                            setting enables autodetection, which is

								#                            the best choice for most installations.

								#

								# net       hostname:port    Network link to a master apcupsd

								#                            through apcupsd's Network Information

								#                            Server. This is used if you don't have

								#                            a UPS directly connected to your computer.

								#

								# snmp      hostname:port:vendor:community

								#                            SNMP Network link to an SNMP-enabled

								#                            UPS device. Vendor is the MIB used by

								#                            the UPS device: can be "APC", "APC_NOTRAP"

								#                            or "RFC" where APC is the powernet MIB,

								#                            "APC_NOTRAP" is powernet with SNMP trap

								#                            catching disabled, and RFC is the IETF's

								#                            rfc1628 UPS-MIB. You usually want "APC".

								#                            Port is usually 161. Community is usually

								#                            "private".

								#

								# dumb      /dev/tty**       Old serial character device for use

								#                            with simple-signaling UPSes.

								#

								# pcnet    ipaddr:username:passphrase

								#                            PowerChute Network Shutdown protocol

								#                            which can be used as an alternative to SNMP

								#                            with AP9617 family of smart slot cards.

								#                            ipaddr is the IP address of the UPS mgmt

								#                            card. username and passphrase are the

								#                            credentials for which the card has been

								#                            configured.

								#

								UPSTYPE apcsmart

								DEVICE /dev/ttyS0


								# LOCKFILE <path to lockfile>

								#   Path for device lock file. Not used on Win32.

								LOCKFILE /var/lock


								# SCRIPTDIR <path to script directory>

								#   Directory in which apccontrol and event scripts are located.

								SCRIPTDIR /etc/apcupsd


								# PWRFAILDIR <path to powerfail directory>

								#   Directory in which to write the powerfail flag file. This file

								#   is created when apcupsd initiates a system shutdown and is

								#   checked in the OS halt scripts to determine if a killpower

								#   (turning off UPS output power) is required.

								PWRFAILDIR /etc


								# NOLOGINDIR <path to nologin directory>

								#   Directory in which to write the nologin file. The existence

								#   of this flag file tells the OS to disallow new logins.

								NOLOGINDIR /etc


								#

								# ======== Configuration parameters used during power failures ==========

								#


								# The ONBATTERYDELAY is the time in seconds from when a power failure

								#   is detected until we react to it with an onbattery event.

								#

								#   This means that, apccontrol will be called with the powerout argument

								#   immediately when a power failure is detected.  However, the

								#   onbattery argument is passed to apccontrol only after the

								#   ONBATTERYDELAY time.  If you don't want to be annoyed by short

								#   powerfailures, make sure that apccontrol powerout does nothing

								#   i.e. comment out the wall.

								#ONBATTERYDELAY 6


								#

								# Note: BATTERYLEVEL, MINUTES, and TIMEOUT work in conjunction, so

								# the first that occurs will cause the initiation of a shutdown.

								#


								# If during a power failure, the remaining battery percentage

								# (as reported by the UPS) is below or equal to BATTERYLEVEL,

								# apcupsd will initiate a system shutdown.

								BATTERYLEVEL 5


								# If during a power failure, the remaining runtime in minutes

								# (as calculated internally by the UPS) is below or equal to MINUTES,

								# apcupsd, will initiate a system shutdown.

								MINUTES 3


								# If during a power failure, the UPS has run on batteries for TIMEOUT

								# many seconds or longer, apcupsd will initiate a system shutdown.

								# A value of 0 disables this timer.

								#

								#  Note, if you have a Smart UPS, you will most likely want to disable

								#    this timer by setting it to zero. That way, you UPS will continue

								#    on batteries until either the % charge remaining drops to or below BATTERYLEVEL,

								#    or the remaining battery runtime drops to or below MINUTES.  Of course,

								#    if you are testing, setting this to 60 causes a quick system shutdown

								#    if you pull the power plug.

								#  If you have an older dumb UPS, you will want to set this to less than

								#    the time you know you can run on batteries.

								TIMEOUT 0


								#  Time in seconds between annoying users to signoff prior to

								#  system shutdown. 0 disables.

								ANNOY 300


								# Initial delay after power failure before warning users to get

								# off the system.

								ANNOYDELAY 60


								# The condition which determines when users are prevented from

								# logging in during a power failure.

								# NOLOGON <string> [ disable | timeout | percent | minutes | always ]

								NOLOGON disable


								# If KILLDELAY is non-zero, apcupsd will continue running after a

								# shutdown has been requested, and after the specified time in

								# seconds attempt to kill the power. This is for use on systems

								# where apcupsd cannot regain control after a shutdown.

								# KILLDELAY <seconds>  0 disables

								KILLDELAY 0


								#

								# ==== Configuration statements for Network Information Server ====

								#


								# NETSERVER [ on | off ] on enables, off disables the network

								#  information server. If netstatus is on, a network information

								#  server process will be started for serving the STATUS and

								#  EVENT data over the network (used by CGI programs).

								NETSERVER on


								# NISIP <dotted notation ip address>

								#  IP address on which NIS server will listen for incoming connections.

								#  This is useful if your server is multi-homed (has more than one

								#  network interface and IP address). Default value is 0.0.0.0 which

								#  means any incoming request will be serviced. Alternatively, you can

								#  configure this setting to any specific IP address of your server and

								#  NIS will listen for connections only on that interface. Use the

								#  loopback address (127.0.0.1) to accept connections only from the

								#  local machine.

								NISIP 0.0.0.0


								# NISPORT <port> default is 3551 as registered with the IANA

								#  port to use for sending STATUS and EVENTS data over the network.

								#  It is not used unless NETSERVER is on. If you change this port,

								#  you will need to change the corresponding value in the cgi directory

								#  and rebuild the cgi programs.

								NISPORT 3551


								# If you want the last few EVENTS to be available over the network

								# by the network information server, you must define an EVENTSFILE.

								EVENTSFILE /var/log/apcupsd.events


								# EVENTSFILEMAX <kilobytes>

								#  By default, the size of the EVENTSFILE will be not be allowed to exceed

								#  10 kilobytes.  When the file grows beyond this limit, older EVENTS will

								#  be removed from the beginning of the file (first in first out).  The

								#  parameter EVENTSFILEMAX can be set to a different kilobyte value, or set

								#  to zero to allow the EVENTSFILE to grow without limit.

								EVENTSFILEMAX 10


								#

								# ========== Configuration statements used if sharing =============

								#            a UPS with more than one machine


								# NETTIME <int>

								#   Interval (in seconds) at which the NIS client polls the server.

								#   Used only when this apcupsd is a network client (UPSTYPE net).

								#NETTIME 60


								#

								# Remaining items are for ShareUPS (APC expansion card) ONLY

								#


								# UPSCLASS [ standalone | shareslave | sharemaster ]

								#   Normally standalone unless you share an UPS using an APC ShareUPS

								#   card.

								UPSCLASS standalone


								# UPSMODE [ disable | share ]

								#   Normally disable unless you share an UPS using an APC ShareUPS card.

								UPSMODE disable


								#

								# ===== Configuration statements to control apcupsd system logging ========

								#


								# Time interval in seconds between writing the STATUS file; 0 disables

								STATTIME 0


								# Location of STATUS file (written to only if STATTIME is non-zero)

								STATFILE /var/log/apcupsd.status


								# LOGSTATS [ on | off ] on enables, off disables

								# Note! This generates a lot of output, so if

								#       you turn this on, be sure that the

								#       file defined in syslog.conf for LOG_NOTICE is a named pipe.

								#  You probably do not want this on.

								LOGSTATS off


								# Time interval in seconds between writing the DATA records to

								#   the log file. 0 disables.

								DATATIME 0


								# FACILITY defines the logging facility (class) for logging to syslog.

								#          If not specified, it defaults to "daemon". This is useful

								#          if you want to separate the data logged by apcupsd from other

								#          programs.

								#FACILITY DAEMON


								#

								# ========== Configuration statements used in updating the UPS EPROM =========

								#


								#

								# These statements are used only by apctest when choosing "Set EEPROM with conf

								# file values" from the EEPROM menu. THESE STATEMENTS HAVE NO EFFECT ON APCUPSD.

								#


								# UPS name, max 8 characters

								#UPSNAME UPS_IDEN


								# Battery date - 8 characters

								#BATTDATE mm/dd/yy


								# Sensitivity to line voltage quality (H cause faster transfer to batteries)

								# SENSITIVITY H M L        (default = H)

								#SENSITIVITY H


								# UPS delay after power return (seconds)

								# WAKEUP 000 060 180 300   (default = 0)

								#WAKEUP 60


								# UPS Grace period after request to power off (seconds)

								# SLEEP 020 180 300 600    (default = 20)

								#SLEEP 180


								# Low line voltage causing transfer to batteries

								# The permitted values depend on your model as defined by last letter

								#  of FIRMWARE or APCMODEL. Some representative values are:

								#    D 106 103 100 097

								#    M 177 172 168 182

								#    A 092 090 088 086

								#    I 208 204 200 196     (default = 0 => not valid)

								#LOTRANSFER  208


								# High line voltage causing transfer to batteries

								# The permitted values depend on your model as defined by last letter

								#  of FIRMWARE or APCMODEL. Some representative values are:

								#    D 127 130 133 136

								#    M 229 234 239 224

								#    A 108 110 112 114

								#    I 253 257 261 265     (default = 0 => not valid)

								#HITRANSFER 253


								# Battery charge needed to restore power

								# RETURNCHARGE 00 15 50 90 (default = 15)

								#RETURNCHARGE 15


								# Alarm delay

								# 0 = zero delay after pwr fail, T = power fail + 30 sec, L = low battery, N = never

								# BEEPSTATE 0 T L N        (default = 0)

								#BEEPSTATE T


								# Low battery warning delay in minutes

								# LOWBATT 02 05 07 10      (default = 02)

								#LOWBATT 2


								# UPS Output voltage when running on batteries

								# The permitted values depend on your model as defined by last letter

								#  of FIRMWARE or APCMODEL. Some representative values are:

								#    D 115

								#    M 208

								#    A 100

								#    I 230 240 220 225     (default = 0 => not valid)

								#OUTPUTVOLTS 230


								# Self test interval in hours 336=2 weeks, 168=1 week, ON=at power on

								# SELFTEST 336 168 ON OFF  (default = 336)

								#SELFTEST 336