You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
506 lines
14 KiB
506 lines
14 KiB
// Pinout configuration
|
|
const int grinderPin = 9, pumpPin = 8, boilerPin = 6, powderPin = 7, wheelPin = 10, invertWheelPin = 11, powderSensorPin = 2, vaporSensorPin = 5, tempSensorPin = A7, wheelStartSensorPin = 4, wheelEndSensorPin = 3, redLED = 13, greenLED = 12;
|
|
|
|
// Global string
|
|
String readString;
|
|
|
|
// Thermistor config
|
|
// WARNING! while the old coffee machine used a PTC thermistor, this was replaced with an NTC one as it was more readily available
|
|
// Code must be adjusted accordingly if a PTC resistor is used once more!
|
|
int Vo;
|
|
float R1 = 10000; // <-- change this value to the resistance of the fixed resistor (so don't change PLS!)
|
|
float logR2, R2, T, Tc, Told;
|
|
float c1 = 8.5e-04, c2 = 1.85e-04, c3 = 2e-07; // Here's where you can perform actual calibration
|
|
|
|
// Variable to store desired Max boiler Temp
|
|
int desiredTemp = 70;
|
|
|
|
// Variables to Store errors:
|
|
int unrecoverableErr = 0;
|
|
int warning = 0;
|
|
int warned = 0; // support variable needed to prevent arduino from making second coffee after refill. this is a shitty hack and resets the board.
|
|
|
|
// Variables for cleaning and other maintenance
|
|
int dry = 0;
|
|
int noCoffee = 0;
|
|
|
|
// Milliseconds to delay between each cycle
|
|
const int milliseconds = 10;
|
|
int timeratio = 1;
|
|
// pumpRatio is = seconds to pump water for and will be updated over serial
|
|
int pumpRatio = 15;
|
|
// This next variable is used to get current "time" in ms and break out of while cycles that need a time limit safeguard
|
|
unsigned long startTime;
|
|
|
|
//_____________________________________________________________________________
|
|
|
|
void(* resetFunc) (void) = 0; // declare reset fuction at address 0
|
|
|
|
//_____________________________________________________________________________
|
|
|
|
void setup() {
|
|
// put your setup code here, to run once:
|
|
// first we set pins as I/O and initialize outputs LOW
|
|
pinMode(boilerPin, OUTPUT); pinMode(pumpPin, OUTPUT); pinMode(grinderPin, OUTPUT); pinMode(powderPin, OUTPUT); pinMode(wheelPin, OUTPUT); pinMode(invertWheelPin, OUTPUT); pinMode (redLED, OUTPUT); pinMode (greenLED, OUTPUT);
|
|
pinMode(powderSensorPin, INPUT); pinMode(vaporSensorPin, INPUT); pinMode(tempSensorPin, INPUT); pinMode(wheelStartSensorPin, INPUT); pinMode(wheelEndSensorPin, INPUT);
|
|
digitalWrite(grinderPin, LOW); digitalWrite(pumpPin, LOW); digitalWrite(boilerPin, LOW); digitalWrite(powderPin, LOW); digitalWrite(wheelPin, LOW); digitalWrite(invertWheelPin, LOW); digitalWrite(redLED, LOW); digitalWrite(greenLED, LOW);
|
|
// timeratio easily allows to determine how many cycles are required to make 1s pass (ms * ratio = 1s)
|
|
timeratio = 1000/milliseconds;
|
|
// initialize serial:
|
|
Serial.begin(9600);
|
|
delay(100);
|
|
Serial.write("Arduino running :)\n");
|
|
}
|
|
|
|
//_____________________________________________________________________________
|
|
|
|
void loop() {
|
|
// put your main code here, to run repeatedly:
|
|
digitalWrite(greenLED, HIGH);
|
|
// Check if unrecoverable error has occurred:
|
|
if (unrecoverableErr == 1) {
|
|
startTime = millis();
|
|
delay(100);
|
|
Serial.write("Error has occurred.\n"); delay(100); Serial.write("Check machine and restart\n");
|
|
digitalWrite(greenLED, LOW);
|
|
while (true){
|
|
digitalWrite(redLED, HIGH);
|
|
delay(1000);
|
|
digitalWrite(redLED, LOW);
|
|
delay(1000);
|
|
// reset arduino after 30s
|
|
if (millis() - startTime == 30000) {
|
|
break;
|
|
}
|
|
}
|
|
resetFunc(); //call reset.
|
|
}
|
|
|
|
// check if data has been sent on serial from ESP or PC:
|
|
if (Serial.available() > 0) {
|
|
// read the incoming data: (we only care about the first few characters, I've chosen 4)
|
|
readString = "";
|
|
serialRead();
|
|
String incomingData = readString.substring(0,4);
|
|
|
|
//if (incomingData == "read") {
|
|
//digitalWrite(greenLED, HIGH);
|
|
//}
|
|
|
|
if (incomingData == "rist") {
|
|
// set parameters for ristretto:
|
|
delay(100);
|
|
Serial.write("Ristretto\n");
|
|
pumpRatio = 10;
|
|
}
|
|
|
|
if (incomingData == "espr") {
|
|
// set parameters for espresso:
|
|
delay(100);
|
|
Serial.write("Espresso\n");
|
|
pumpRatio = 13;
|
|
}
|
|
|
|
if (incomingData == "long") {
|
|
// set parameters for lungo:
|
|
delay(100);
|
|
Serial.write("Lungo\n");
|
|
pumpRatio = 16;
|
|
}
|
|
|
|
// check if the incoming data is "make":
|
|
if (incomingData == "make") {
|
|
// run the code to make coffee:
|
|
delay(100);
|
|
Serial.write("Making some coffee!\n");
|
|
makeCoffee();
|
|
}
|
|
|
|
if (incomingData == "dryr") {
|
|
// run the code to make a dry run (no powder, no water):
|
|
delay(100);
|
|
Serial.write("DryRun\n");
|
|
dry = 1;
|
|
makeCoffee();
|
|
}
|
|
|
|
if (incomingData == "noco") {
|
|
// run the code to make a dry run (no powder, nor water):
|
|
delay(100);
|
|
Serial.write("NoCo\n");
|
|
pumpRatio = 12;
|
|
noCoffee = 1;
|
|
makeCoffee();
|
|
}
|
|
|
|
if (incomingData == "grin") {
|
|
// only grind
|
|
Grind();
|
|
}
|
|
|
|
if (incomingData == "pump") {
|
|
// run the code to just pump water:
|
|
pumpRatio = 15;
|
|
Pump();
|
|
}
|
|
|
|
if (incomingData == "pres") {
|
|
// only press
|
|
Press();
|
|
}
|
|
|
|
if (incomingData == "unpr") {
|
|
// only unpress
|
|
unPress();
|
|
}
|
|
|
|
if (incomingData == "heat") {
|
|
// only heat
|
|
desiredTemp = 80;
|
|
Heat();
|
|
}
|
|
|
|
if (incomingData == "drop") {
|
|
// only drop
|
|
Drop();
|
|
}
|
|
|
|
if (incomingData == "clea") {
|
|
// clean machine
|
|
delay(100);
|
|
Serial.write("s-clean\n");
|
|
dry = 1;
|
|
makeCoffee();
|
|
noCoffee = 1;
|
|
makeCoffee();
|
|
delay(100);
|
|
Serial.write("S-cleaning done.\n");
|
|
}
|
|
}
|
|
|
|
// making steam:
|
|
while (digitalRead(vaporSensorPin) == HIGH) {
|
|
desiredTemp = 90;
|
|
Serial.write("Vapor heating\n");
|
|
delay(500);
|
|
Heat(); // Heat the boiler to vapor temperature
|
|
delay(20000);
|
|
|
|
if (unrecoverableErr == 1) {
|
|
break;
|
|
}
|
|
}
|
|
delay(milliseconds);
|
|
}
|
|
|
|
//_____________________________________________________________________________
|
|
|
|
// this is how we read the input
|
|
void serialRead() {
|
|
while (Serial.available()) {
|
|
delay(10);
|
|
if (Serial.available() > 0) {
|
|
char c = Serial.read();
|
|
readString += c;}
|
|
}
|
|
}
|
|
|
|
//_____________________________________________________________________________
|
|
|
|
void Grind() {
|
|
digitalWrite(greenLED, LOW);
|
|
delay(100);
|
|
Serial.write("grinding...\n");
|
|
digitalWrite(grinderPin, HIGH);
|
|
startTime = millis();
|
|
while (true) {
|
|
delay(milliseconds);
|
|
if (digitalRead(powderSensorPin) == HIGH) {
|
|
digitalWrite(grinderPin, LOW);
|
|
delay(100);
|
|
Serial.write("Grinding Done\n");
|
|
break;
|
|
}
|
|
if (millis() - startTime > 15000) {
|
|
Serial.write("Warning, grinding took too long!\n");
|
|
digitalWrite(grinderPin, LOW);
|
|
delay(100);
|
|
Serial.write("Out of Coffee?\n");
|
|
warning = 1;
|
|
warned = 1;
|
|
break;
|
|
}
|
|
}
|
|
digitalWrite(greenLED, HIGH);
|
|
}
|
|
|
|
//_____________________________________________________________________________
|
|
|
|
void Drop() {
|
|
digitalWrite(greenLED, LOW);
|
|
delay(100);
|
|
Serial.write("dropping...\n");
|
|
digitalWrite(powderPin, HIGH);
|
|
delay(1000);
|
|
digitalWrite(powderPin, LOW);
|
|
delay(100);
|
|
Serial.write("Dropped\n");
|
|
digitalWrite(greenLED, HIGH);
|
|
}
|
|
|
|
//_____________________________________________________________________________
|
|
|
|
void Heat() {
|
|
digitalWrite(greenLED, LOW);
|
|
digitalWrite(redLED, HIGH);
|
|
startTime = millis();
|
|
delay(100);
|
|
Serial.write("Heating to ");
|
|
delay(100);
|
|
Serial.print(desiredTemp);
|
|
delay(100);
|
|
Tc = 0;
|
|
Told = - 100;
|
|
|
|
// monitor temperature and adjust boilerPin as needed:
|
|
while (true) {
|
|
|
|
// read temperature from tempSensorPin:
|
|
Vo = analogRead(tempSensorPin);
|
|
R2 = R1 * (1023.0 / (float)Vo - 1.0);
|
|
logR2 = log(R2);
|
|
T = (1.0 / (c1 + c2*logR2 + c3*logR2*logR2*logR2));
|
|
Tc = (T - 273.15);
|
|
|
|
if (millis() - startTime == 1000) {
|
|
Told = Tc; // support variable to store temp at beginning, so that we can be sure it's increasing
|
|
}
|
|
|
|
// check if temperature is within the acceptable range and break out of the loop without error if done heating:
|
|
if (Tc > desiredTemp) {
|
|
// temperature is within range, so break out of the loop:
|
|
digitalWrite(boilerPin, LOW);
|
|
delay(100);
|
|
Serial.write("reached desired temp\n");
|
|
delay(100);
|
|
Serial.print(Tc);
|
|
delay(100);
|
|
digitalWrite(redLED, LOW);
|
|
break;
|
|
}
|
|
|
|
if (Tc < -100) {
|
|
delay(100);
|
|
Serial.write("u-Thermocouple: unplugged or failed\n");
|
|
digitalWrite(boilerPin, LOW);
|
|
unrecoverableErr = 1;
|
|
break;
|
|
}
|
|
|
|
if (millis() - startTime > 20000 && Tc - Told < 1) {
|
|
delay(100);
|
|
Serial.write("p-Thermocouple: positioning or relay fault\n");
|
|
digitalWrite(boilerPin, LOW);
|
|
unrecoverableErr = 1;
|
|
break;
|
|
}
|
|
|
|
if (millis() - startTime > 30000) {
|
|
delay(100);
|
|
Serial.write("h-taking too long, continuing...\n");
|
|
digitalWrite(boilerPin, LOW);
|
|
digitalWrite(redLED, LOW);
|
|
break;
|
|
}
|
|
|
|
// We do this at the end so that the relay is not uselessly cycled
|
|
digitalWrite(boilerPin, HIGH);
|
|
delay(milliseconds);
|
|
|
|
}
|
|
digitalWrite(greenLED, HIGH);
|
|
}
|
|
|
|
//_____________________________________________________________________________
|
|
|
|
void Press() {
|
|
digitalWrite(greenLED, LOW);
|
|
delay(100);
|
|
Serial.write("pressing...\n");
|
|
|
|
// Reset Press before every coffee
|
|
digitalWrite(invertWheelPin, HIGH);
|
|
delay(1000);
|
|
digitalWrite(invertWheelPin, LOW);
|
|
|
|
digitalWrite(wheelPin, HIGH);
|
|
startTime = millis();
|
|
|
|
while (true) {
|
|
delay(milliseconds);
|
|
if (digitalRead(wheelEndSensorPin) == HIGH) {
|
|
delay(900); // extra delay added to compensate for slightly incorrect endstop placement after repair
|
|
digitalWrite(wheelPin, LOW);
|
|
delay(100);
|
|
Serial.write("Pressed\n");
|
|
break;
|
|
}
|
|
if (millis() - startTime > 15000) {
|
|
delay(100);
|
|
Serial.write("p-end of pressing not detected\n");
|
|
digitalWrite(wheelPin, LOW);
|
|
unrecoverableErr = 1;
|
|
break;
|
|
}
|
|
}
|
|
digitalWrite(greenLED, HIGH);
|
|
}
|
|
|
|
//_____________________________________________________________________________
|
|
|
|
void unPress() {
|
|
digitalWrite(greenLED, LOW);
|
|
delay(100);
|
|
Serial.write("unPressing...\n");
|
|
|
|
// Reset Press before every coffee
|
|
digitalWrite(wheelPin, HIGH);
|
|
delay(1500);
|
|
digitalWrite(wheelPin, LOW);
|
|
|
|
digitalWrite(invertWheelPin, HIGH);
|
|
startTime = millis();
|
|
|
|
while (true) {
|
|
delay(milliseconds);
|
|
if (digitalRead(wheelStartSensorPin) == HIGH) {
|
|
delay(1500);
|
|
digitalWrite(invertWheelPin, LOW);
|
|
delay(100);
|
|
Serial.write("UnPressed\n");
|
|
break;
|
|
}
|
|
if (millis() - startTime > 15000) {
|
|
delay(100);
|
|
Serial.write("u-end of unPressing not detected\n");
|
|
digitalWrite(invertWheelPin, LOW);
|
|
unrecoverableErr = 1;
|
|
break;
|
|
}
|
|
}
|
|
digitalWrite(greenLED, HIGH);
|
|
}
|
|
|
|
//_____________________________________________________________________________
|
|
|
|
void Pump() {
|
|
digitalWrite(greenLED, LOW);
|
|
delay(100);
|
|
Serial.write("pumping Water...\n");
|
|
digitalWrite(pumpPin, HIGH);
|
|
delay(1000*pumpRatio);
|
|
digitalWrite(pumpPin, LOW);
|
|
delay(100);
|
|
Serial.write("Pumping water done\n");
|
|
digitalWrite(greenLED, HIGH);
|
|
}
|
|
|
|
//_____________________________________________________________________________
|
|
|
|
void makeCoffee() {
|
|
// code to make coffee goes here...
|
|
// It would be much smarter to break down complicated functions into subroutines: press/unpress etc...
|
|
// Hence that's what we'll have done by the time the first release goes public ;)
|
|
// makeCoffee() can still run all the same, but clean() can use the same press/unpress code!
|
|
// care must be taken to place these functions earlier in the code, or the compiler will rightfully freak out
|
|
|
|
while (true) {
|
|
|
|
desiredTemp = 75;
|
|
Heat(); // First we pre-heat the boiler
|
|
if (unrecoverableErr == 1) {
|
|
break;
|
|
}
|
|
|
|
if (dry == 0 && noCoffee == 0) {
|
|
Grind(); // Grinding some nice roasted coffee beans!
|
|
}
|
|
|
|
// If grinder won't stop, coffee probably needs to be refilled.
|
|
if (warning == 1) {
|
|
delay(100);
|
|
Serial.write("refill coffee and send cont command\n");
|
|
while (true) {
|
|
// check if data has been sent on serial from ESP or PC:
|
|
if (Serial.available() > 0) {
|
|
// read the incoming data: (we only care about the first few characters, I've chosen 4)
|
|
readString = "";
|
|
serialRead();
|
|
String incomingData = readString.substring(0,4);
|
|
|
|
if (incomingData == "cont") {
|
|
// coffee refilled, making is allowed to continue
|
|
Serial.write("Refilled\n");
|
|
warning = 0;
|
|
Grind(); // Grinding some nice roasted coffee beans!
|
|
if (warning == 1) {
|
|
unrecoverableErr = 1;
|
|
Serial.write("g-failure: second grinding failure, check grinder!\n");
|
|
}
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
}
|
|
|
|
// Stop if grinding failed a second time
|
|
if (unrecoverableErr == 1) {
|
|
break;
|
|
}
|
|
|
|
delay(1000); // this delay is mandatory to prevent powder spillage caused by grinder inertia.
|
|
unPress(); // unpressing the press to reset the machine
|
|
|
|
if (unrecoverableErr == 1) {
|
|
break;
|
|
}
|
|
|
|
Drop(); // Dropping the powder in the press
|
|
delay(1000);
|
|
|
|
Press(); // Self explainatory
|
|
|
|
if (unrecoverableErr == 1) {
|
|
break;
|
|
}
|
|
|
|
desiredTemp = 85;
|
|
Heat(); // First we pre-heat the boiler
|
|
if (unrecoverableErr == 1) {
|
|
break;
|
|
}
|
|
|
|
if (dry == 0) {
|
|
digitalWrite(boilerPin, HIGH);
|
|
delay(100);
|
|
Pump(); // Pump ratio (in seconds) will be read from serial input in final release
|
|
digitalWrite(boilerPin, LOW);
|
|
}
|
|
delay(3000); // Allow pressure to wane
|
|
|
|
unPress(); // unpressing the press to reset the machine
|
|
|
|
if (unrecoverableErr == 1) {
|
|
break;
|
|
}
|
|
delay(100);
|
|
Serial.write("Complete!\n");
|
|
delay(1000);
|
|
dry = 0;
|
|
noCoffee = 0;
|
|
if (warned == 1) {
|
|
resetFunc(); //call reset. I am ashamed of this, but it works.
|
|
}
|
|
break;
|
|
}
|
|
}
|